# abs_profile_v8.ini (Oct 25 2026): FINAL/abs_profile_v2.ini (easy-peel raft rule v2, unchanged) + anti-stringing for a 4-part plate.
# raft 3 layers (1 base + 2 interface), 0.3 mm contact gap, interface lines 0.5 mm apart (not solid), 1.5 mm expansion, no brim/skirt.
printer_technology = FFF
bed_shape = 0x0,150x0,150x150,0x150
max_print_height = 150
nozzle_diameter = 0.4
filament_diameter = 1.75
gcode_flavor = reprap
use_relative_e_distances = 1

first_layer_height = 0.2
top_solid_layers = 4
bottom_solid_layers = 4
support_material_style = grid
support_material_pattern = rectilinear-grid
support_material_spacing = 1.8
support_material_with_sheath = 1
support_material_threshold = 45
support_material_buildplate_only = 1
support_material_contact_distance = 0.2
support_material_interface_layers = 2
support_material_interface_spacing = 0.5
support_material_speed = 20
brim_separation = 0

temperature = 240
first_layer_temperature = 240
bed_temperature = 100
first_layer_bed_temperature = 100
disable_fan_first_layers = 5
min_fan_speed = 0
max_fan_speed = 0
bridge_fan_speed = 0

first_layer_speed = 4
first_layer_extrusion_width = 200%
perimeter_speed = 30
external_perimeter_speed = 20
small_perimeter_speed = 20
infill_speed = 35
solid_infill_speed = 30
top_solid_infill_speed = 20
bridge_speed = 20

deretract_speed = 25

start_gcode = M140 S[first_layer_bed_temperature]\nM104 S0 ; avoid simultaneous full-power bed/nozzle heating\nG90\nM83\nG28\nM320 ; activate saved Repetier auto-level matrix\nM190 S[first_layer_bed_temperature]\nM104 S[first_layer_temperature]\nM109 S[first_layer_temperature]\nG1 Z5 F1200
end_gcode = G1 E-1 F900\nG91\nG1 Z5 F600\nG90\nG1 X5 Y140 F3000\nM400\nM104 S0\nM140 S0\nM84
autoemit_temperature_commands = 1

support_material = 0
support_material_auto = 0
thumbnails = 
brim_type = no_brim
brim_width = 0
layer_height = 0.2
raft_layers = 3
raft_contact_distance = 0.3
raft_expansion = 0
skirts = 0
skirt_distance = 0
perimeters = 4
fill_density = 40%
fill_pattern = gyroid
support_material_interface_contact_loops = 0
elefant_foot_compensation = 0.2
# --- v8 anti-stringing (travel between parts) ---
retract_length = 1.8
retract_speed = 35
retract_before_travel = 1
retract_layer_change = 1
wipe = 1
retract_before_wipe = 70%
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 0
only_retract_when_crossing_perimeters = 0
travel_speed = 100
retract_lift = 0.4
seam_position = aligned
raft_first_layer_expansion = 2
# raft_expansion 1.5 -> 0: PrusaSlicer otherwise closed the clips' jaw gaps with raft interface (33% of the thick clip's jaw-gap centre covered at 1.5, 0% at 0).
# The raft TOP now sits only under solid part footprint; the 0.2 mm raft BASE still sticks out 2 mm all round as the peel lip.